Search Results

Search found 1111 matches

Author Message
Topic: Oh Dear... Rhippy Gots Him Some News Today
Anti_A

Replies: 11
Views: 145

PostForum: Copter-X Helicopters   Posted: Fri Nov 20, 2009 10:43 pm   Subject: Oh Dear... Rhippy Gots Him Some News Today
Congrats matey.

if you're lucky it may be a 600 nitro! (c;
Topic: A trip to the Dark Side for a new project
Anti_A

Replies: 108
Views: 1302

PostForum: Off Topic   Posted: Thu Nov 19, 2009 10:51 pm   Subject: A trip to the Dark Side for a new project
Do one that will take a trex 600 motor (c:
Topic: A trip to the Dark Side for a new project
Anti_A

Replies: 108
Views: 1302

PostForum: Off Topic   Posted: Thu Nov 19, 2009 8:11 pm   Subject: A trip to the Dark Side for a new project
Nice one mate!

so what's next?
Topic: A trip to the Dark Side for a new project
Anti_A

Replies: 108
Views: 1302

PostForum: Off Topic   Posted: Tue Nov 17, 2009 9:24 pm   Subject: A trip to the Dark Side for a new project
I've got a swift II which I use as a warm up plane, the hog was a repair and flew fine last outing, I did put an alien command on it but took it off before the flight, checked the tx settings and they ...
Topic: A trip to the Dark Side for a new project
Anti_A

Replies: 108
Views: 1302

PostForum: Off Topic   Posted: Sun Nov 15, 2009 10:18 pm   Subject: A trip to the Dark Side for a new project
It looks better than my Hog, it went in rather hard and found some trees.

http://www.heliguy.com/Forum/images/userpix/8431_PB150005_1.jpg

http://www.heliguy.com/Forum/images/userpix/8431_PB15000 ...
Topic: A trip to the Dark Side for a new project
Anti_A

Replies: 108
Views: 1302

PostForum: Off Topic   Posted: Sat Nov 14, 2009 12:46 am   Subject: A trip to the Dark Side for a new project
glyn check this out

[youtube]http://www.youtube.com/watch?v=NZtqZ2UhnDg[/youtube]

this way once the plane is built you can set the cog by adjusting battery etc.
Topic: Rhippys wagging tail
Anti_A

Replies: 13
Views: 129

PostForum: Copter-X Helicopters   Posted: Fri Nov 13, 2009 11:53 pm   Subject: Rhippys wagging tail
The less than 50 = rate mode depends on transmitter.

Spektrum has +0 to +100 and -0 to -100 so in effect you can have less than 50% in both heading hold and rate modes.

Rhip if the gyro has dela ...
Topic: Alien Command Advanced
Anti_A

Replies: 10
Views: 272

PostForum: Belt CP   Posted: Fri Nov 13, 2009 7:24 pm   Subject: Alien Command Advanced
Hi, the above posts are correct, the alien command advanced will work on a belt cp with the mixing switched off on the tx, however this disables idle up and puts channel 6 on the top left dial trim w ...
Topic: Connect AR6200 DSM2 6-channel receiver to Twister Hawk 4in1
Anti_A

Replies: 1
Views: 181

PostForum: Radio Receivers   Posted: Sun Nov 08, 2009 8:32 pm   Subject: Connect AR6200 DSM2 6-channel receiver to Twister Hawk 4in1
I think this may help you.

I've tested on an esky 4 in 1 and it works great!

http://www.rcgroups.com/forums/showthread.php?p=7095078#post7095078
Topic: Foam cutting for wings , your help needed.
Anti_A

Replies: 24
Views: 156

PostForum: Off Topic   Posted: Fri Nov 06, 2009 7:46 pm   Subject: Foam cutting for wings , your help needed.
You must have an old pc power supply knocking about, that plus a dimmer switch should work fine.

G
Topic: Imax B6 Rubbish
Anti_A

Replies: 10
Views: 152

PostForum: Battery Chargers   Posted: Tue Nov 03, 2009 1:50 pm   Subject: Imax B6 Rubbish
Looks like a job for me tomorrow (c:

sounds like the board has gone on the balance plug connector.
Topic: Esky ET61 6-channel Tx and Rx setup.
Anti_A

Replies: 12
Views: 380

PostForum: Interceptor 400   Posted: Sun Nov 01, 2009 10:17 pm   Subject: Esky ET61 6-channel Tx and Rx setup.
Yeah moving the conrtol rods in towards the servo horn center will give less throw and so make it less sensitive, the pitch is ok as it is but if you change the length of the connector rod you will al ...
Topic: Advice for next purchase
Anti_A

Replies: 29
Views: 248

PostForum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion.   Posted: Thu Oct 29, 2009 9:56 pm   Subject: Advice for next purchase
Nitro chicken death dance.... a total Ba%$&*%d to expeirence, especially if the throttle servo jams full open Shocked

you have to wait for the natural death of the heli.

Electrics normally ...
Topic: Advice for next purchase
Anti_A

Replies: 29
Views: 248

PostForum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion.   Posted: Thu Oct 29, 2009 9:35 pm   Subject: Advice for next purchase
oh noes! the funky chicken dance of doom!


gah I hate that

<even worse with nitros!>
Topic: Advice for next purchase
Anti_A

Replies: 29
Views: 248

PostForum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion.   Posted: Thu Oct 29, 2009 9:26 pm   Subject: Advice for next purchase
jeez that must have been a firework display of a crash!


idle up don't you just luurve it \c:

it should have a voice activated cut off, you just shout "OH S$%* Noooooeeeeee" and it cuts off (c:
Topic: Advice for next purchase
Anti_A

Replies: 29
Views: 248

PostForum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion.   Posted: Thu Oct 29, 2009 9:08 pm   Subject: Advice for next purchase
yeah well wait till you have a knock )c: they give in faster than the French (c; and sometimes they don't die outright but just pull lots of current throungh the esc, draining power from the RX untill ...
Topic: Advice for next purchase
Anti_A

Replies: 29
Views: 248

PostForum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion.   Posted: Thu Oct 29, 2009 8:55 pm   Subject: Advice for next purchase
Servos are best bought on a price per skill level imho

if you are learning to fly then cheap servos will give best value for money, if you are into full fast forward flight and some mild 3d, etc th ...
Topic: intercepter kit / acerlab g100
Anti_A

Replies: 1
Views: 88

PostForum: Interceptor 400   Posted: Thu Oct 29, 2009 2:58 pm   Subject: intercepter kit / acerlab g100
Hi, the pinions that come with the kit are for lower speed motors, the acerlab motor is designed to go with the pinion I think its 13T, any higher toothed pinion can result in too high a headspeed, th ...
Topic: Esky ET61 6-channel Tx and Rx setup.
Anti_A

Replies: 12
Views: 380

PostForum: Interceptor 400   Posted: Thu Oct 29, 2009 2:55 pm   Subject: Esky ET61 6-channel Tx and Rx setup.
Hi Ben, glad you got it sorted, I should try to get on the forums more often (c:

I'm still trying to put some guides together for different tx's etc. When I get time.



Gary.

Cheers for th ...
Topic: intercepter 400 tail control.
Anti_A

Replies: 2
Views: 58

PostForum: The Panic Forum !!!!!   Posted: Wed Oct 28, 2009 8:08 pm   Subject: intercepter 400 tail control.
Make sure the tail rotor control balls are on the leading edge of the blade grips, so the servo moves into the body to turn the heli nose to the right.

If they are on the lagging edge it takes too ...
Topic: FUTABA S9206s NEEDED
Anti_A

Replies: 13
Views: 146

PostForum: Servo's   Posted: Sat Oct 24, 2009 6:07 pm   Subject: FUTABA S9206s NEEDED
Sorry mate still no go, can't get the staff mate.
Topic: What charger can charge a battery with all cells below 2v
Anti_A

Replies: 8
Views: 192

PostForum: Battery Chargers   Posted: Fri Oct 23, 2009 9:57 pm   Subject: What charger can charge a battery with all cells below 2v
Not any longer mate.

[youtube]http://www.youtube.com/watch?v=AMxjKtY1Z_M[/youtube]
Topic: Lipo battery at 2v per cell?
Anti_A

Replies: 8
Views: 145

PostForum: Batteries.   Posted: Fri Oct 23, 2009 9:56 pm   Subject: Lipo battery at 2v per cell?
yup you got it.

[youtube]http://www.youtube.com/watch?v=AMxjKtY1Z_M[/youtube]

how much is a 10 cell one ?
Topic: What charger can charge a battery with all cells below 2v
Anti_A

Replies: 8
Views: 192

PostForum: Battery Chargers   Posted: Fri Oct 23, 2009 7:33 pm   Subject: What charger can charge a battery with all cells below 2v
If you have a flat battery (under 3.1v/cell) can your charger charge it?

Can it charge a battery that has 1v/cell?

If it can what charger are you using?
Topic: Lipo battery at 2v per cell?
Anti_A

Replies: 8
Views: 145

PostForum: Batteries.   Posted: Fri Oct 23, 2009 7:31 pm   Subject: Lipo battery at 2v per cell?
OK say you've had a good flight and you go that little too far, your battery cell voltage has dropped to 2v per cell or less what do you do?

All times are GMT - 1 Hours

Page 1 of 45

Page: 1, 2, 3 ... 43, 44, 45  Next

Jump to:  
heliguy illustration