Search found 81 matches
| Author | Message |
|---|---|
| Topic: Rear stablelizers postion + Control arm | |
| TwisterStu Replies: 11 Views: 139 |
 Forum: HoneyBee King (Collective Pitch) Posted: Tue Nov 25, 2008 3:54 pm Subject: Rear stablelizers postion + Control arm |
| Might try that! I notice you dont seem to be using the servo link guides?
You find thats better? |
|
| Topic: Rear stablelizers postion + Control arm | |
| TwisterStu Replies: 11 Views: 139 |
Forum: HoneyBee King (Collective Pitch) Posted: Mon Nov 24, 2008 3:33 pm Subject: Rear stablelizers postion + Control arm |
| Can you recomend any aftermarkey tail servo mounts? | |
| Topic: Rear stablelizers postion + Control arm | |
| TwisterStu Replies: 11 Views: 139 |
Forum: HoneyBee King (Collective Pitch) Posted: Mon Nov 24, 2008 2:49 pm Subject: Rear stablelizers postion + Control arm |
| What are those servo clamps? The plastic ones are tight but there is still plenty of movement and flex in mine! | |
| Topic: Rear stablelizers postion + Control arm | |
| TwisterStu Replies: 11 Views: 139 |
Forum: HoneyBee King (Collective Pitch) Posted: Mon Nov 24, 2008 1:27 pm Subject: Rear stablelizers postion + Control arm |
| http://www.heliguy.com/Forum/images/userpix/7938_king1_1.jpg
http://www.heliguy.com/Forum/images/userpix/7938_king2_1.jpg http://www.heliguy.com/Forum/images/userpix/7938_king3_1.jpg |
|
| Topic: Rear stablelizers postion + Control arm | |
| TwisterStu Replies: 11 Views: 139 |
Forum: HoneyBee King (Collective Pitch) Posted: Mon Nov 24, 2008 12:59 pm Subject: Rear stablelizers postion + Control arm |
| Where do you have yours? And whats the best way of securing them?
My vertical one keeps rotating and turning into the blades due to the chopper spinning and I am wrecking rear blades. Could this al ... |
|
| Topic: Help with Xtreme tail shaft, please. | |
| TwisterStu Replies: 21 Views: 316 |
Forum: HoneyBee King (Collective Pitch) Posted: Thu Oct 23, 2008 11:47 am Subject: Help with Xtreme tail shaft, please. |
| it looks back to front! the tooth bit should be the other way round and then the flange slips onto the left of it! It the cog bit secured or can you take it off> | |
| Topic: carbon boom | |
| TwisterStu Replies: 9 Views: 247 |
Forum: HoneyBee King (Collective Pitch) Posted: Mon Sep 29, 2008 9:36 am Subject: carbon boom |
| I found they were a mm os so thinner. I had problems with them slipping and needed to put a thin piece of tape around the end. I also found that the tail link guides and stablelizers would be loose an ... | |
| Topic: Most awkward job on the HBK2 | |
| TwisterStu Replies: 29 Views: 505 |
Forum: HoneyBee King (Collective Pitch) Posted: Mon Sep 29, 2008 7:39 am Subject: Most awkward job on the HBK2 |
| Try changing the tail shaft! Cant get the damn thing off! now I have switched to the alloy box I cant get the rotor and slider off!
I managed to snap the slide ball joint trying to pull the blade h ... |
|
| Topic: Warning! Please take care in this hobby! Serious injurys! | |
| TwisterStu Replies: 16 Views: 539 |
Forum: Damage Report Posted: Wed Jun 25, 2008 8:36 pm Subject: Warning! Please take care in this hobby! Serious injurys! |
| Sight is getting better now! Still not 100% but I can see but a bit blury! | |
| Topic: V2 Tail issue and vibration | |
| TwisterStu Replies: 2 Views: 161 |
Forum: Twister RC helicopters Posted: Sun Jun 22, 2008 5:14 pm Subject: V2 Tail issue and vibration |
| Hi, Just wondering, My V2 keeps spining unless i cut the tail rotor.
Its like the tail is generating more thurst than the main blades! Why is this? I have tried two main motors and they both do the ... |
|
| Topic: Warning! Please take care in this hobby! Serious injurys! | |
| TwisterStu Replies: 16 Views: 539 |
Forum: Damage Report Posted: Sun Jun 15, 2008 3:48 pm Subject: Warning! Please take care in this hobby! Serious injurys! |
| I am posting this to warn others to take care in this hobby!
I have just come out of hospital form an overnight stay with one eye less working! I was fixing my Twister V2, and was holding it min ... |
|
| Topic: Gryo wont set | |
| TwisterStu Replies: 3 Views: 126 |
Forum: HoneyBee King (Collective Pitch) Posted: Fri Jun 13, 2008 9:41 am Subject: Gryo wont set |
| I noticed that my hh dosent set if the motor is unplugged fully. maybe it requires feedback from the motor? | |
| Topic: Tail Rotor Shaft | |
| TwisterStu Replies: 6 Views: 182 |
Forum: HoneyBee King (Collective Pitch) Posted: Fri Jun 06, 2008 7:26 pm Subject: Tail Rotor Shaft |
| I seem to have had the belt a bit too tige, and now the tail shaft pully teeth are chewed to bits.
I cant seem to see it listed, what part is it under? Cheers |
|
| Topic: the better you get the harder you crash | |
| TwisterStu Replies: 4 Views: 223 |
Forum: HoneyBee King (Collective Pitch) Posted: Sat May 31, 2008 6:06 pm Subject: the better you get the harder you crash |
| DOH! I have now got my bird flying! I can now hover around a bit and land and ok for a batt almost!
Apart from I need to learn to stop trying to fly indoors as my rooms are too small! This time ... |
|
| Topic: SG90 Servos | |
| TwisterStu Replies: 6 Views: 291 |
Forum: HoneyBee King (Collective Pitch) Posted: Sat May 31, 2008 4:25 pm Subject: SG90 Servos |
| I hear plenty of folks use these! Do I need to modify the heli to take these? or do they just slot in?
Cheers |
|
| Topic: Carbon blade repairs. | |
| TwisterStu Replies: 3 Views: 193 |
Forum: HoneyBee King (Collective Pitch) Posted: Fri May 30, 2008 4:21 pm Subject: Carbon blade repairs. |
| There just cpl small hols in the middle of the edges! nothing major, just didnt want the blades to get worse and to stop the noise of the air rushing over! | |
| Topic: Carbon blade repairs. | |
| TwisterStu Replies: 3 Views: 193 |
Forum: HoneyBee King (Collective Pitch) Posted: Fri May 30, 2008 2:33 pm Subject: Carbon blade repairs. |
| Is it ok to put resin on the blades to repair minor holes? The training gear caught caught and the blades hit the road for a few seconds and the very end of the tips have small holes in them!
I was ... |
|
| Topic: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box | |
| TwisterStu Replies: 11 Views: 424 |
Forum: Special Requests Posted: Fri May 23, 2008 4:37 am Subject: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box |
| YES SOLD! THANKS | |
| Topic: YEAH! & NEIGH!! | |
| TwisterStu Replies: 7 Views: 197 |
Forum: HoneyBee King (Collective Pitch) Posted: Thu May 22, 2008 2:57 pm Subject: YEAH! & NEIGH!! |
| Stu, the carbons sound nice and all, but are you at that stage yet? The woodies have their detractors, but they help save the rest of the airframe if nicked by doing the exploding thing.
Along with t ... |
|
| Topic: YEAH! & NEIGH!! | |
| TwisterStu Replies: 7 Views: 197 |
Forum: HoneyBee King (Collective Pitch) Posted: Thu May 22, 2008 11:33 am Subject: YEAH! & NEIGH!! |
| After months of not having the bird flying waiting on parts. I finally got the HBK ready today.
I have spent the last week or so tottaly stipping her down, with new frame, tail boom blades and othe ... |
|
| Topic: Belt tension | |
| TwisterStu Replies: 5 Views: 209 |
Forum: HoneyBee King (Collective Pitch) Posted: Thu May 22, 2008 11:01 am Subject: Belt tension |
| Whats the best way of adjusting it?
Every time I seem to pull the boom back the belt just pulls it back in again!  |
|
| Topic: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box | |
| TwisterStu Replies: 11 Views: 424 |
Forum: Special Requests Posted: Wed May 21, 2008 5:44 pm Subject: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box |
| Yea but you wait a month! these have cost me almost £80 now, they are £60 in UK | |
| Topic: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box | |
| TwisterStu Replies: 11 Views: 424 |
Forum: Special Requests Posted: Wed May 21, 2008 5:07 pm Subject: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box |
| Im looking for around £40 shipped! $45 works out about £20 at current rate, sorry! | |
| Topic: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box | |
| TwisterStu Replies: 11 Views: 424 |
Forum: Special Requests Posted: Mon May 19, 2008 4:44 pm Subject: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box |
| here you go!
http://www.heliguy.com/Forum/images/userpix/7938_parts_1.jpg |
|
| Topic: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box | |
| TwisterStu Replies: 11 Views: 424 |
Forum: Special Requests Posted: Mon May 19, 2008 3:04 pm Subject: FOR SALE: Honey Bee King 2 FULL CNC Alloy head and tail box |
| I am selling the full CNC head and tail box including swashplate.
These are brand new in the pack still! I am only selling as I was waiting over 2 months for the parts and ended up getting them ... |
|
