Search found 958 matches
| Author | Message |
|---|---|
| Topic: Tail Fin Vibrates and landing Skids | |
| geoff Replies: 3 Views: 151 |
 Forum: Walkera 22, 35, 36, 52 and 60. Posted: Wed May 27, 2009 6:37 pm Subject: Tail Fin Vibrates and landing Skids |
| hi ramal
vibration can be caused by a split in the frame. check the whole frame over by slightly twisting each part this will show any breaks in the frame. i had a fram break after a crash and this ... |
|
| Topic: walkera 36 with a slow tail rotor | |
| geoff Replies: 7 Views: 232 |
Forum: Walkera 22, 35, 36, 52 and 60. Posted: Thu Apr 23, 2009 7:55 am Subject: walkera 36 with a slow tail rotor |
| hi
check the tail belt drive pinion (cog). this is driven by a small pin and easily wears / shears the drive. if you hold the main drive wheel and try to rotate the tail by hand you will see the cog ... |
|
| Topic: Walkera 36 - no Signal | |
| geoff Replies: 4 Views: 201 |
Forum: Walkera 22, 35, 36, 52 and 60. Posted: Thu Nov 27, 2008 4:32 pm Subject: Walkera 36 - no Signal |
| hi ramall
bringer of bad news i'm affraid 
the transmitter and reciever must be of the same type when dealing with walkera equiptment. you cannot mix and match 
geoff |
|
| Topic: walkera 35 shaft drive/ belt drive | |
| geoff Replies: 2 Views: 466 |
Forum: Walkera 22, 35, 36, 52 and 60. Posted: Wed Jun 04, 2008 3:46 pm Subject: walkera 35 shaft drive/ belt drive |
| hi
im fairly sure the walkera 36 parts will fit your 35. youy will need the main gear wheel, the belt drive gears and the 36 tail boom and tail complete. why do you want to change to a belt anyway? ... |
|
| Topic: falcon main shaft and drive gear change | |
| geoff Replies: 2 Views: 249 |
Forum: Falcon 3D Posted: Thu May 22, 2008 9:54 am Subject: falcon main shaft and drive gear change |
| hi there
try the link below it should help you out geoff http://www.heliguy.com/Forum/falcon3d-head-upgrade-t7978.html |
|
| Topic: newbie from Spain | |
| geoff Replies: 2 Views: 349 |
Forum: New Members - Introduce yourself Here! Posted: Sat Apr 12, 2008 9:50 am Subject: newbie from Spain |
| hi colin
welcome to the forum. you have bought yourself a nice hali there, its a little lively but great to learn with. happy hovering. geoff |
|
| Topic: what engine will fit | |
| geoff Replies: 4 Views: 388 |
Forum: Other RC Helicopters Posted: Wed Apr 09, 2008 3:57 pm Subject: what engine will fit |
| hi sport
if you visit a site called just engines you will find their prices for new engines very competative. their spares are also cheap and the service is second to none. geoff |
|
| Topic: Help with HBCP-2 Gyro callibration | |
| geoff Replies: 7 Views: 822 |
Forum: HoneyBee CP3, mods, upgrades and older models. Posted: Fri Mar 21, 2008 12:06 pm Subject: Help with HBCP-2 Gyro callibration |
| hi
set the gain to its mid point and proportional also to the mid point. try your heli. move the proportional with the power off a very small amount either way then power up the heli again. note i ... |
|
| Topic: Adding in additional connectors between ESC ad battery? | |
| geoff Replies: 2 Views: 401 |
Forum: Belt CP V2, mods, upgrades and older models. Posted: Wed Mar 19, 2008 10:34 am Subject: Adding in additional connectors between ESC ad battery? |
| hi gerd
i run three helis, two have deans connections the other has bullit connection. i made up a lead to use the deans on all three using a short length of cable with a male deans on one end and t ... |
|
| Topic: Rolling around like a top...please help me... | |
| geoff Replies: 5 Views: 220 |
Forum: HoneyBee King 3, mods, upgrades and older models. Posted: Wed Mar 19, 2008 10:23 am Subject: Rolling around like a top...please help me... |
| hi
if the gyro is loose the tail would spin uncontrollably. as the gyro would be compensating for itselfe instead of your heli. depending on the type of gyro it should be mounted either horizontally ... |
|
| Topic: Rolling around like a top...please help me... | |
| geoff Replies: 5 Views: 220 |
Forum: HoneyBee King 3, mods, upgrades and older models. Posted: Wed Mar 19, 2008 9:28 am Subject: Rolling around like a top...please help me... |
| hi samoozle
carefully check the heli's frame, in the crash it might of broken in one or two places. i had this happen to my 36 and it took ages before i found the break(i was at the point of slingin ... |
|
| Topic: moderators???? | |
| geoff Replies: 3 Views: 259 |
Forum: Belt CP V2, mods, upgrades and older models. Posted: Sat Mar 15, 2008 10:53 am Subject: moderators???? |
| hi ARMOURKING
if you think there are posts here requireing sticky status please name them and i will look into it for you. thanks geoff |
|
| Topic: Motor cut outs! | |
| geoff Replies: 12 Views: 521 |
Forum: HoneyBee King 3, mods, upgrades and older models. Posted: Thu Mar 13, 2008 11:47 am Subject: Motor cut outs! |
| hi qazxsw
it sounds like the esc is powering down due to it thinking the battery voltage is low. all esc's have this function to prevent the battery from being dischared too much. unfortunatly i do ... |
|
| Topic: lipo cell cover torn | |
| geoff Replies: 3 Views: 449 |
Forum: Batteries. Posted: Thu Mar 13, 2008 11:39 am Subject: lipo cell cover torn |
| hi theresacsl
any damage to a lipo battery no matter how small should be concidered as scrap. these are very volitile chemical batterys and can go on fire with only the smallest defect. allthou ... |
|
| Topic: oops i've lost my transmitter settings walkera #83 nitro | |
| geoff Replies: 3 Views: 1614 |
Forum: Walkera 4#3, 5#5, 4 and other models. Posted: Fri Mar 07, 2008 8:46 pm Subject: oops i've lost my transmitter settings walkera #83 nitro |
| hi scooter
thanks for your reply. i have set up the transmitter to move the servos in the correct directions but when i ask for throttle up the two front servos move in the right direction but the r ... |
|
| Topic: oops i've lost my transmitter settings walkera #83 nitro | |
| geoff Replies: 3 Views: 1614 |
Forum: Walkera 4#3, 5#5, 4 and other models. Posted: Thu Mar 06, 2008 7:32 pm Subject: oops i've lost my transmitter settings walkera #83 nitro |
| hi to all.
i have inadvertantly reset my settings on my walkera #83 transmitter. 
its the WK-0703 tranny. can anyone out there please post or pm the setting for me. for the life of me i cant ge ... |
|
| Topic: Falcon dies after a few secs | |
| geoff Replies: 7 Views: 839 |
Forum: Falcon 3D Posted: Sun Feb 03, 2008 9:07 pm Subject: Falcon dies after a few secs |
| hi darren
did you fly your heli before charging the battery when you first recieved it? have you flown your heli until the battery was flat? if you answere yes to any of the above i suspect your ba ... |
|
| Topic: moter or not | |
| geoff Replies: 9 Views: 407 |
Forum: Falcon 3D Posted: Mon Jan 28, 2008 6:31 pm Subject: moter or not |
| hi flyer1
it sounds like your motor has burnt out.
the standard motor on my falcon only lasted a few flights before giving up. this seams to be a common problem on the falcon. geoff |
|
| Topic: falcon | |
| geoff Replies: 4 Views: 560 |
Forum: I'm a stupid newbie, help me! Posted: Wed Jan 09, 2008 4:46 pm Subject: falcon |
| hi adrian
check the gears are meshed together correctly. check to make sure the cogs are not spinning on the drive shaft. both of the above will reduce the power to the tail rotor therefore causing ... |
|
| Topic: Replacing the rotor head on my CP2 | |
| geoff Replies: 2 Views: 950 |
Forum: HoneyBee CP3, mods, upgrades and older models. Posted: Thu Jan 03, 2008 3:41 pm Subject: Replacing the rotor head on my CP2 |
| hi woody
try this link it might help you out. http://www.heliguy.com/Forum/main-shaft-removal-cp2-t3229.html geoff |
|
| Topic: 36 tail upgrade | |
| geoff Replies: 1 Views: 665 |
Forum: Walkera 22, 35, 36, 52 and 60. Posted: Fri Dec 28, 2007 1:51 pm Subject: 36 tail upgrade |
| hi mac 1
the pictures in the link [url=http://www.heliguy.com/Forum/walkera-36-from-scratch-t1555.html]here might help you out. the upgrade has the same basic assembly as the original tail system. ... |
|
| Topic: CNC SLOPPY UNRESPONSIVE | |
| geoff Replies: 3 Views: 410 |
Forum: Walkera 22, 35, 36, 52 and 60. Posted: Fri Dec 28, 2007 1:45 pm Subject: CNC SLOPPY UNRESPONSIVE |
| hi
if you have the walkera upgraded head there is an arm attached to the blade holder which has the ball link attached to it. i have found that this can twist outside the holder therefore altering p ... |
|
| Topic: tooth missing | |
| geoff Replies: 2 Views: 392 |
Forum: Falcon 3D Posted: Mon Dec 17, 2007 5:55 pm Subject: tooth missing |
| hi flyer 1
my falcon ran for a long time without any problems with a couple of teeth missing from the tail drive gear. but once i started to give the tail a hard time re flying in stronger winds and ... |
|
| Topic: petrol blockade this weekend. | |
| geoff Replies: 63 Views: 982 |
Forum: Off Topic Posted: Fri Dec 14, 2007 2:51 pm Subject: petrol blockade this weekend. |
| totally agree with Breitling here, if nobody panicked their would be enough petrol to last for a week or so.
i passed a garage on my way into work this morning and people were filling petrol cans up. ... |
|
| Topic: new and clueless | |
| geoff Replies: 2 Views: 254 |
Forum: New Members - Introduce yourself Here! Posted: Fri Dec 14, 2007 2:26 pm Subject: new and clueless |
| hi matt
welcome to our forum. 
feel free to ask as many questions as you like as we all learn off each other. speed freak  well join the club .
happy hovering. geoff |
|
