Search found 654 matches
| Author | Message |
|---|---|
| Topic: Problem switching to DX6i on my Belt CP with Sonix 30A ESC | |
| lankey Replies: 14 Views: 191 |
 Forum: Belt CP Posted: Sun Nov 30, 2008 10:23 am Subject: Problem switching to DX6i on my Belt CP with Sonix 30A ESC |
Dang.... hate being no help! 
Ian, tell you what helped me no-end when setting up my DX7. Finless Bob! Over at Helifreak there's a range of vids for the Trex450SE (build and general videos). ... |
|
| Topic: Delight, relief, achievement, and inevitably - a shunt... | |
| lankey Replies: 2 Views: 80 |
Forum: Belt CP Posted: Sun Nov 30, 2008 6:35 am Subject: Delight, relief, achievement, and inevitably - a shunt... |
Hey, that's fantastic mate... well chuffed for you 
I know you've had problems with the heli of late, and taking the oppertunity to fit SG90's was a good move. It's weird after so much frustrati ... |
|
| Topic: Belt CP Motor Dead | |
| lankey Replies: 8 Views: 88 |
Forum: Belt CP Posted: Sun Nov 30, 2008 5:20 am Subject: Belt CP Motor Dead |
| Hi fspees
Had a similar thing happen to me after a crash... the stock ESC decided it had had enough of being in "break-off" and flipped into "break-on"! Very strange, and that had me stumped for a ... |
|
| Topic: Problem switching to DX6i on my Belt CP with Sonix 30A ESC | |
| lankey Replies: 14 Views: 191 |
Forum: Belt CP Posted: Sat Nov 29, 2008 11:48 am Subject: Problem switching to DX6i on my Belt CP with Sonix 30A ESC |
| Hi Ian
The stock gyro obviousely has no remote gain function, so any gyro/gain settings in the DX6i shouldn't make any difference. What way round are you connecting up- turn on Tx then heli still a ... |
|
| Topic: How to use the Stock Belt CP controller in training mode ? | |
| lankey Replies: 1 Views: 99 |
Forum: Belt CP Posted: Sat Nov 29, 2008 6:32 am Subject: How to use the Stock Belt CP controller in training mode ? |
| Hi
Had a quick read-up on this: Position the "Pitch" and "Trim" knobs to zero. Remove the Tx crystal (otherwise you can cause some damage) Remove batterys and locate the jumper switches (lable ... |
|
| Topic: Weird sound coming from main gear | |
| lankey Replies: 19 Views: 341 |
Forum: Belt CP Posted: Sat Nov 29, 2008 5:43 am Subject: Weird sound coming from main gear |
| Well done mate.
What seems like a simple job can turn into a nightmare without the proper tools.... been there far too many times!
Good luck with the flight. Regards Steve |
|
| Topic: Adjustable Bell Mixer Pushrod link | |
| lankey Replies: 1 Views: 86 |
Forum: Belt CP Posted: Thu Nov 27, 2008 10:33 am Subject: Adjustable Bell Mixer Pushrod link |
| Hi mate
I presume you've been looking at the setup sticky with regard to adjusting the tracking. Personally I wouldn't worry about the mod, just buy yourself some Extreme Productions Titanium Turnb ... |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Tue Nov 25, 2008 9:46 pm Subject: CopterX head upgrade question |
| conex
The CX tail is a straight swap. If you buy the complete tail then it comes with a belt- which I've opted to use as I've heard the stock belt doesn't mesh great with the CX tail drive. The ... |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Tue Nov 25, 2008 7:56 pm Subject: CopterX head upgrade question |
| Hi Alan
Only a couple of times mate. Should have bought a big expensive Airfix model instead!
Trust me, when the CX head and tail are on, I'll be grabbing every chilly, cold-fingered oper ... |
|
| Topic: Just my Luck )c| | |
| lankey Replies: 8 Views: 115 |
Forum: Belt CP Posted: Tue Nov 25, 2008 4:23 pm Subject: Just my Luck )c| |
| Troy
Think you have issues mate... what is that Avatar all about!
Nice one Steve |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Tue Nov 25, 2008 4:17 pm Subject: CopterX head upgrade question |
| Hi VoS
Pm'd you info on uk suppliers, failing that check out flebay! What I'm using for the conversion: CX V2 head (CX450-01-20) CX linkage rod set (just incase) Ball link reamer (some of t ... |
|
| Topic: difference between upgraded belt cp & more expensive cho | |
| lankey Replies: 10 Views: 189 |
Forum: Belt CP Posted: Mon Nov 24, 2008 6:23 am Subject: difference between upgraded belt cp & more expensive cho |
| Ooooooh, DG- you are a one! |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Mon Nov 24, 2008 5:14 am Subject: CopterX head upgrade question |
| Phil
Know what you mean about time mate. Had the CX stuff for nearly three weeks and only started fitting it in earnest yesterday... and I've not even got kids like you! Would think the CX stuff ca ... |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Sun Nov 23, 2008 11:37 am Subject: CopterX head upgrade question |
| Phil
The re-build of the CX is an absolute must!! When the head's brand new most of the screws are not locktighted and the thrust bearings are "dry". If you don't do it you really are putting yours ... |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Sun Nov 23, 2008 10:22 am Subject: CopterX head upgrade question |
| Hi Phil
Spent some time reading posts and asking a few questions over in the CX forum. As it turns out, the Align blades are a little tight in the grips! Most people seem to give it a good wiggle a ... |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Sat Nov 22, 2008 8:28 pm Subject: CopterX head upgrade question |
| Never used them mate but they are probably quite good. If you are ever unsure about the CX stuff, ask the guys over at the CX forum... that's what I did when I had specific questions to ask.
Regard ... |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Sat Nov 22, 2008 7:21 pm Subject: CopterX head upgrade question |
| I think the CX V2 flybar is thicker than the Esky one. My head didn't come with a flybar so I got myself an Align 220mm. To use the stock paddles, I would think you would need to drill out the metal w ... | |
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Sat Nov 22, 2008 6:46 pm Subject: CopterX head upgrade question |
| Hi mate
Contarary to the general concensus on Esky CNC, I've had no complaints regarding the swashplate! After reading your reply I ran upstairs, pulled out my Esky CNC swash, removed one of the sw ... |
|
| Topic: Finally got to fly it with SG90s - crashed. Advice please. | |
| lankey Replies: 33 Views: 336 |
Forum: Belt CP Posted: Sat Nov 22, 2008 1:39 pm Subject: Finally got to fly it with SG90s - crashed. Advice please. |
| Mate, glad you like the SG90's, I know many peeps including myself love them for the money! Regarding Trex canopys. Any of the 450 size will fit and you'll be glad you got one: clears your elevator ho ... | |
| Topic: Weird sound coming from main gear | |
| lankey Replies: 19 Views: 341 |
Forum: Belt CP Posted: Sat Nov 22, 2008 9:52 am Subject: Weird sound coming from main gear |
| I agree Andy
Pinion won't solve the original question... good to know though
Regards Steve |
|
| Topic: Weird sound coming from main gear | |
| lankey Replies: 19 Views: 341 |
Forum: Belt CP Posted: Sat Nov 22, 2008 8:25 am Subject: Weird sound coming from main gear |
| Whato
If you experience bad mesh with the MX400/stock pinion give an Extreme Productions pinion- available under King 2 upgrades. Much longer teeth and I find a great mesh with the Helimax gear. ... |
|
| Topic: CopterX head upgrade question | |
| lankey Replies: 27 Views: 455 |
Forum: Belt CP Posted: Sat Nov 22, 2008 8:18 am Subject: CopterX head upgrade question |
| Hi jolo
I'm I'm the process of swapping over to the CX head but I've got the UGT-05 swash to play around with. Can't understand why you would only swap two of the four balls. As you state, the CX l ... |
|
| Topic: Damaged my belt cp blades today will king2 fit & work ok | |
| lankey Replies: 13 Views: 215 |
Forum: Belt CP Posted: Sat Nov 22, 2008 6:33 am Subject: Damaged my belt cp blades today will king2 fit & work ok |
| Hi guys
Boy are those Align fibers strong! That's exactly why I don't use them anymore! Had one crash with them and (only a small one) the blades just chopped up any part of the heli they touched.. ... |
|
| Topic: Finally got to fly it with SG90s - crashed. Advice please. | |
| lankey Replies: 33 Views: 336 |
Forum: Belt CP Posted: Sat Nov 22, 2008 5:20 am Subject: Finally got to fly it with SG90s - crashed. Advice please. |
| Like old times eh Nigel |
|
| Topic: Finally got to fly it with SG90s - crashed. Advice please. | |
| lankey Replies: 33 Views: 336 |
Forum: Belt CP Posted: Sat Nov 22, 2008 5:12 am Subject: Finally got to fly it with SG90s - crashed. Advice please. |
| Hi mate
Yeah, piccies would be handy. Do you have the ball links on the inside of the servo horn? If not swap them over. The SG90 horns are longer than stock, you could trim the tips of the hor ... |
|
