Search found 266 matches
| Author | Message |
|---|---|
| Topic: centering servo horn on the tail | |
| o0dekker0o Replies: 2 Views: 97 |
 Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Wed Oct 01, 2008 5:18 am Subject: centering servo horn on the tail |
| i don't get any creep when i don't use sub trim
i got it, it works perfectly now my gyro and servo combo is the Align RCE600 and DS520 digi servo |
|
| Topic: centering servo horn on the tail | |
| o0dekker0o Replies: 2 Views: 97 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Tue Sep 30, 2008 9:31 pm Subject: centering servo horn on the tail |
| if i can't get the horn perfectly at 90 do i sub trim it using SERVO into RX directly or use RATE mode ? | |
| Topic: gyro setup on trex 450 | |
| o0dekker0o Replies: 7 Views: 251 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Tue Sep 30, 2008 9:35 am Subject: gyro setup on trex 450 |
| thanks, i think i can only have SW-GYRO or F.MODE
should i just stick with SW-GYRO ? 80% on both to start with ? |
|
| Topic: gyro setup on trex 450 | |
| o0dekker0o Replies: 7 Views: 251 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Tue Sep 30, 2008 8:00 am Subject: gyro setup on trex 450 |
| ok thats good, but (DX6i) what do i do to the menus..i'm a newbie
The first menu is when my flight mode switch is set to NORMAL and it displays SW-GYRO, do i leave it in this mode or go to SW-F.MOD ... |
|
| Topic: gyro setup on trex 450 | |
| o0dekker0o Replies: 7 Views: 251 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Tue Sep 30, 2008 5:16 am Subject: gyro setup on trex 450 |
| Using DX6i
I’m setting up my gyro now and i’m in the gyro menu, the TX displays <- (arrow left) RATE SW-GYRO 0: <- 80.0% 1: 25.9% When i flick the switch down the ... |
|
| Topic: trex 450 cyclic | |
| o0dekker0o Replies: 10 Views: 208 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Tue Sep 30, 2008 5:15 am Subject: trex 450 cyclic |
| I've been told by a pro 3d flyers that a lot of 450's have that issue and it's not a problem, the centralises out anyway and doesn't affect flight. | |
| Topic: woodies blades for trex 450 | |
| o0dekker0o Replies: 5 Views: 139 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Tue Sep 30, 2008 5:13 am Subject: woodies blades for trex 450 |
| i think the blade grips are still too wide to make them move almost freely, thats why i suggested sanding. | |
| Topic: woodies blades for trex 450 | |
| o0dekker0o Replies: 5 Views: 139 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Mon Sep 29, 2008 6:12 pm Subject: woodies blades for trex 450 |
| wiggle until they can just stand up by themselves or so they are still firm, i want them to survive a blade hit and not bend the main shaft. | |
| Topic: woodies blades for trex 450 | |
| o0dekker0o Replies: 5 Views: 139 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Mon Sep 29, 2008 5:58 pm Subject: woodies blades for trex 450 |
| I bought some trex blades (woodies) for my trex. V2 SE carbon / cnc head. The blades have plastic mounts but seem really tight in the blades grips. Should i sand them down a little so the plastic bit ... | |
| Topic: trex 450 cyclic | |
| o0dekker0o Replies: 10 Views: 208 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Mon Sep 29, 2008 11:41 am Subject: trex 450 cyclic |
| yeah they are correct, rods are the same length anyway. | |
| Topic: trex 450 cyclic | |
| o0dekker0o Replies: 10 Views: 208 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Mon Sep 29, 2008 10:56 am Subject: trex 450 cyclic |
| weird...
i have v2 carbon, same. the head was mostly built apart from the cage, i followed page 6 instructions and built it. It's like there is something missing between the metal flybar contro ... |
|
| Topic: trex 450 cyclic | |
| o0dekker0o Replies: 10 Views: 208 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Mon Sep 29, 2008 6:47 am Subject: trex 450 cyclic |
| thanks for the info, what about my slack on the cage video, is that normal ? | |
| Topic: trex 450 cyclic | |
| o0dekker0o Replies: 10 Views: 208 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Sun Sep 28, 2008 8:54 pm Subject: trex 450 cyclic |
| Getting pretty far now building my trex 450, have some questions...can you respond below my questions ?
1) I’ve been watching Bob’s videos as it’s the only hands on source i have at the moment,I’ve ... |
|
| Topic: 2mm screw bolts needed | |
| o0dekker0o Replies: 2 Views: 92 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Sun Sep 28, 2008 8:37 pm Subject: 2mm screw bolts needed |
| ok cool | |
| Topic: 2mm screw bolts needed | |
| o0dekker0o Replies: 2 Views: 92 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Sun Sep 28, 2008 3:51 pm Subject: 2mm screw bolts needed |
| I have installed my gyro with 4 x 2mm threaded screws and need some bolts for the other side. They will be the same size as the bolt that holds the head on the main shaft. Where can i get some from ? ... | |
| Topic: cables came out of the gyro plug !!! | |
| o0dekker0o Replies: 4 Views: 88 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Sat Sep 27, 2008 7:15 pm Subject: cables came out of the gyro plug !!! |
| sounds good, what about soldering to the gold connector, i have a micro solder kit, i can pass the cable through the first crimp and then solder onto the connector with a spot. | |
| Topic: cables came out of the gyro plug !!! | |
| o0dekker0o Replies: 4 Views: 88 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Sat Sep 27, 2008 5:43 pm Subject: cables came out of the gyro plug !!! |
| I was pulling the gyro plug out of my RX and 2 of the 3 wires popped out from the plug !!!!
Can i uncrimp the plug somehow or maybe solder it back in somehow ?!! |
|
| Topic: RCE 600 gyro tuning | |
| o0dekker0o Replies: 7 Views: 184 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Mon Sep 22, 2008 2:13 pm Subject: RCE 600 gyro tuning |
| where do you get your align velcro from ?
If you are placing the heli like the picture (dont mind you cant see the tail, just so you understand me right). http://www.heliguy.com/Forum/images/u ... |
|
| Topic: RCE 600 gyro tuning | |
| o0dekker0o Replies: 7 Views: 184 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Fri Sep 19, 2008 6:44 pm Subject: RCE 600 gyro tuning |
| yup got it, i got it right. | |
| Topic: RCE 600 gyro tuning | |
| o0dekker0o Replies: 7 Views: 184 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Fri Sep 19, 2008 5:47 pm Subject: RCE 600 gyro tuning |
| (5) Put the gyro in headlock mode and turn the heli right. You should see the tail move the same way as if you applied left stick (as per (1)).
So if i turn the heli so the nose is right the tail f ... |
|
| Topic: dx6i not working on second power up | |
| o0dekker0o Replies: 0 Views: 84 |
Forum: Radio Transmitters. Posted: Thu Sep 18, 2008 12:58 pm Subject: dx6i not working on second power up |
| Bah! Looks like my dx6i is messed up, it's brand new
All the servos, gyro and esc are in the RX, i turn on the TX, then connect the battery, both lights some on and hey , it works. If i turn it ... |
|
| Topic: RCE 600 gyro tuning | |
| o0dekker0o Replies: 7 Views: 184 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Thu Sep 18, 2008 6:51 am Subject: RCE 600 gyro tuning |
| I now have my gyro in place with the wires facing the rear of the heli, I am using a DX6i Radio
see pics http://www.heliguy.com/Forum/images/userpix/1436_PICT5768_1.jpg http://www.heliguy.c ... |
|
| Topic: how to mount RCE 600 gyro | |
| o0dekker0o Replies: 3 Views: 99 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Wed Sep 17, 2008 7:24 pm Subject: how to mount RCE 600 gyro |
| so wires going to the boom tail | |
| Topic: how to mount RCE 600 gyro | |
| o0dekker0o Replies: 3 Views: 99 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Wed Sep 17, 2008 6:50 pm Subject: how to mount RCE 600 gyro |
| How should my gyro go ?
Say i’m going to install it on top, i’ve also switched it to digital Servo Pic 5765 – red side up, wires leading back Pic 5766 – red facing back, wire to the left of ... |
|
| Topic: how to mount tail servo | |
| o0dekker0o Replies: 4 Views: 107 |
Forum: Trex 450 XL and SE. Electronics, radios, set up, resources and discussion. Posted: Tue Sep 16, 2008 8:24 am Subject: how to mount tail servo |
| yeah i have a digi servo | |
