Well iv`e decided to sell my Protech 450 IC Nitro helicopter as many of you will know that i have just moved up to a 50 Size nitro and this is no longer needed. This Zoom 450IC was one of the 1st dozen kits of this helicopter in the UK at the time of buying.
The only parts that was included was the Engine , Blades and Heli Assembled. That alone cost me over £200 when new !!! I had to buy everything else and it was not cheap. This costs £249 *NEW* with Servos installed excluding Gyro as of today.
This has had about 5-6 hours flying (if that) since i have brought it. This has been well looked after and is setup for my own personal style of flying, which is +14 to -14 Swash pitch range from within the transmitter (not supplied).
This Zoom 450 IC fly`s like its on steroids, It ascends like a rocket at insane speed when you give it full throttle. This does Chaos and Tic-Tocs very quickly, so much that i have had to dial down the EXPO on my Transmitter to NEGATIVE 30 !!!
This is UNCRASHED !!!!!
Recently replaced a B206 servo on the cyclic (1 month ago) as the other one stopped working at a cost of £17.50 !!
Pictures below:
What instructions are included ???
Protech Zoom 450 IC manual, Origional Canopy that shipped with the Helicopter (slightly scratched on Black Window) and Origional Yellow shipping box.
What is installed on this Helicopter ???
Engine:
Protech SX12 Nitro which is run on 20% WildCat " HeliMix " since brought.
It has got a Remote Glow Adapter installed and works faultlessly.
This engine has been properly run in and has got just about over 2 1/2 turns on the needle fuel valve, if memory serves me right.
Servos:
3 x Protech B206 (blue) on the Cyclic (£46.50) Speed (sec): 0.17, Torque (Kg.cm): 2.00
1 x Protech B206 (blue) on the Throttle (£15.50) Speed (sec): 0.17, Torque (Kg.cm): 2.00
1 x Futaba S3153 on the Tail (£26.99) Torque :1.5kg(4.8V) or 1.7kg(6.0V) Speed: 0.10S (4.8V) or 0.09S (6.0V)
Gyro:
Protech NT420 heading hold gyro (about £25) is installed but needs setting up as it has been put on to replace a GY401 which is now on the 600N.
Blades:
Protech 350mm Wooden ones installed. (£15)
Reciever battery:
1 x 4.8V 2400mah nimh packs with Futaba charging lead attached. (£7.50) It has also got a Voltspy 3 installed which will show you how much charge you have in the Receiver batteries (not connected at present). Their is a Futaba on/off switch installed on the helicopter.
Custom Canopy:
1 x *UNFLOWN* Orange and White (Professionally sprayed) Canopy with Flossie and Heliguy.com on it. This alone cost me £35 !!! I can not find this at present but i know i still have it.
Spares:
1 x Main Rotor Blade Set (T0502.037) *NEW*
1 x Fuel Tank set (T0503.024)
1 x Tail Transmission Gear (T0503.023) *NEW*
1 x Muffler Gasket Set (T0503.012), 1 used out of 10.
1 x Engine Cooling Fan (T0503.025) *NEW*
2 x Hex Start Adapter (T0503.014), 3 left out of 4.
1 x Linkage Set (T0503.001) *NEW*
1 x Clutch Liner (T0503.011) *NEW*
What is NOT included:
Anything that is not listed in this advert that is for sale. This means, Receiver, Transmitter , All Starter Equipment, Fuel, Charger.
Delivery:
about £12 which will possibly require a signature on delivery.
Make me a offer over £130 and i might accept it !!! As i need the money for another project !!!!!!
Please PM me on the forum or to make a offer.
_________________
Thanks, Paul
Futaba FF7 2.4Ghz
Trex 600NSP R617FS, OS50H, S9254 & Gy401, 3x 5625MG + 625MG
Boomerang 40 R606FS, SC46 Engine
Imax B5, Cellpro 4S
